These wooden chairs with armrests wide enough to hold them drink or bowl of snacks, complete with a small table, ideal combination for a pleasant stay outside.
Original name of this popular chair is Adirondek (Adirondack), named so to Adirondek mountains in the United States (New York), where in 1903, Thomas Lee (Thomas Lee) made the first such chair.
The boards (preferably pine)
Plywood or hardboard Template
Screws 40 mm
2 liters of coatings for wood
2 liters of paint (acrylic or enamel)
How to make a wooden chair in the yard or terrace
List of cutting (for 2 seats):
4 x pages of seats (33 x 5 x 0.8 inch)
18 x slats for the seat (23 x 23 x 0.8 inch)
4 x front legs (20 x 5.6 x 0.8 inch)
4 x armrests (27 x 5.6 x 20.8 inch)
4 x supports the armrests (5.1 x 3.5 x 0.8 inch)
2 x central strips backrest (30 x 3.5 x 0.8 inch)
8 x transverse strips back of the backrest (30 x 3.3 x 0.8 inch)
2 x upper crosspiece back of the backrest (28 x 2.1 x 0.8 inch)
2 x lower transverse slat back of the backrest (23 x 2.1 x 0.8 inch)
On the plywood panel dimensions 33 x 5.1 inch draw a pattern on the basis of the chair to the top of the sketch. Cut out the template and use it to highlight the contours of the basics of surfing dimensions 33 x 5.1 x 0.8 inch which will then cut by sawing.
Delete the top edge 9 slats for the seat (585 x 55 x 22mm) and attach them to the page between points A and B with sketches, taking into account that they are evenly sorted.
The two front legs (23 x 5.6 x 0.8 inch) cut so that the lower part is narrower 20mm from the upper part (as in the above illustration). On a completely flat surface support the front of the seat to the rear “foot” lying on the ground, then attach the front legs on both sides so that the narrower portion toward the rear.
Lay a strip of 30 x 5.6 x 0.8 inch on a flat surface and left and right of it after 2 strips of 30 x 3.3 x 0.8 inch (total 5 slats). With the focal point of using ropes and pencil, draw a semicircle on the upper side moldings and then trim to C drawn line. Then again place the strips on a flat surface or them evenly apart. Attach them to the bottom of the šrafeći them closer to the edge of the lower transverse strips (23x 2.1 x 0.8 inch), taking into account that are parallel. Then screw the upper crosspiece (28 x 2.1 x 0.8 inch) at a distance of 12.9 inch from the bottom rail. Please note that in the lower part of Screws slats to the transverse rail, while the upper part of the Screws transverse rail of the back slats.
Screw the backrest on the seat, right behind the last slats.
On the plywood panel, draw a template for the armrest (toward the top drawing). Over template then download the drawing back of the board (27 x 5.6 x 0.8 inch). Cut the board, grind and sand the edges, then attach the arm rests first on the upper ends of the front legs, then the ends of the upper crosspiece that feeds the left and right of the back.
For the armrests need one strut (5.1 x 3.5 x 0.8 inch). Cut the curved shape and attach it to the underside of the armrest and page feet (one backed for each side).
How to make a wooden table for the garden or terrace
List of cutting (Table 1):
5 x boards for the desktop (19.6 x 3.7 x 0.8 inch)
2 x transverse strips (19 x 1.1 x 0.8 inch)
2 x legs (22 x 5.6 x 0.8 inch)
2 x lateral rungs (16 x 3.7 x 0.8 inch)
2 x pins (15 x 5.6 x 0.8 inch)
On a flat surface, place 5 planks of the upper work surface of the table (500 x 3.7 x 0.8 inch), ensuring that parallel and with a gap of 0.19 inch between the two boards. Sand the ends of the cross bar (19 x 1.1 x 0.8 inch) and attach it to the underside of the planks, so be1.67 inch from the ends of planks. (The distance between these two cross rails should be 16.3 inch).
Attach the side rungs (16 x 3.7 x 0.8 inch) at the legs (22 x 5.6 x 0.8 inch), at a height of 3.5 inch from the base.
Draw and cut out a template for pins (as in the top figure) and then transfer it to the board for pins (15.7 x 5.6 x 0.8 inch). Cut and run legs, then fasten to the exterior of the legs, just below the side rungs.
Rotate the table upside down and place it on the middle legs that you attached to the transverse rails.
Process the remaining sharp edges, fill screw holes with wood putty and sand the all available surfaces. Repaint furniture coating for wood, then apply two to three coats of acrylic or enamel paint for outdoor use.